Cisco, Networking

OSPF PART II | Dokumentasi.

 

 

Router A

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se 3/0
Router(config-if)#ip add 10.10.1.1 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#
%LINK-5-CHANGED: Interface Serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up

Router(config-if)#exit
Router(config)#int se 2/0
Router(config-if)#ip add 10.10.2.1 255.255.255.252
Router(config-if)#clock rate 9600
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config-if)#exit
Router(config)#int fa 7/0
Router(config-if)#ip add 10.10.5.1 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet7/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet7/0, changed state to up

Router(config-if)#exit
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.10 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#router ospf 90
Router(config-router)#network 10.10.1.0 255.255.255.252 area 9
Router(config-router)#network 10.10.2.0 255.255.255.252 area 9
Router(config-router)#network 10.10.5.0 255.255.255.252 area 9
Router(config-router)#network 192.168.1.0 255.255.255.0 area 9
Router(config-router)#log-adjancency-changes
^
% Invalid input detected at ‘^’ marker.

Router(config-router)#log-adjacency-changes
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#write

Router B

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se 2/0
Router(config-if)#ip add 10.10.2.2 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config-if)#exit
Router(config)#int se 3/0
Router(config-if)#ip add 10.10.3.1 255.255.255.252
Router(config-if)#clock rate 9600
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#
%LINK-5-CHANGED: Interface Serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up

Router(config-if)#exit
Router(config)#int fa7/0
Router(config-if)#ip add 10.10.6.1 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet7/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet7/0, changed state to up

Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/0
Router(config-if)#ip address 192.168.3.10 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#%IP-4-DUPADDR: Duplicate address 192.168.3.10 on FastEthernet0/0, sourced by 0006.2A08.30B1

Router(config-if)#exit
Router(config)#router ospf 90
Router(config-router)#network 10.10.2.0 255.255.255.252
% Incomplete command.
Router(config-router)#network 10.10.2.0 255.255.255.252 area 9
Router(config-router)#network 10.10.2.0 255.255.255.252 area 9
00:35:55: %OSPF-5-ADJCHG: Process 90, Nbr 192.168.1.10 on Serial2/0 from LOADING to FULL, Loading Done

Router(config-router)#network 10.10.3.0 255.255.255.252 area 9
Router(config-router)#network 10.10.6.0 255.255.255.252 area 9
Router(config-router)#network 192.168.3.0 255.255.255.0 area 9
Router(config-router)#log adjacency-changes
^
% Invalid input detected at ‘^’ marker.

Router(config-router)#log-adjacency-changes
Router(config-router)#end

%SYS-5-CONFIG_I: Configured from console by console
Router#write
Building configuration…
[OK]

Router C

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se 2/0
Router(config-if)#ip add 10.10.2.2 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config-if)#exit
Router(config)#int se 3/0
Router(config-if)#ip add 10.10.3.1 255.255.255.252
Router(config-if)#clock rate 9600
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#
%LINK-5-CHANGED: Interface Serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up

Router(config-if)#exit
Router(config)#int fa7/0
Router(config-if)#ip add 10.10.6.1 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet7/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet7/0, changed state to up

Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/0
Router(config-if)#ip address 192.168.3.10 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#%IP-4-DUPADDR: Duplicate address 192.168.3.10 on FastEthernet0/0, sourced by 0006.2A08.30B1

Router(config-if)#exit
Router(config)#router ospf 90
Router(config-router)#network 10.10.2.0 255.255.255.252
% Incomplete command.
Router(config-router)#network 10.10.2.0 255.255.255.252 area 9
Router(config-router)#network 10.10.2.0 255.255.255.252 area 9
00:35:55: %OSPF-5-ADJCHG: Process 90, Nbr 192.168.1.10 on Serial2/0 from LOADING to FULL, Loading Done

Router(config-router)#network 10.10.3.0 255.255.255.252 area 9
Router(config-router)#network 10.10.6.0 255.255.255.252 area 9
Router(config-router)#network 192.168.3.0 255.255.255.0 area 9
Router(config-router)#log adjacency-changes
^
% Invalid input detected at ‘^’ marker.

Router(config-router)#log-adjacency-changes
Router(config-router)#end

%SYS-5-CONFIG_I: Configured from console by console
Router#write
Building configuration…
[OK]

Router D

Router(config)#int se 3/0
Router(config-if)#ip add 10.10.4.2 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#int fa 7/0
Router(config-if)#ip add 10.10.5.2
% Incomplete command.
Router(config-if)#ip add 10.10.5.2 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet7/0, changed state to down
Router(config-if)#
%LINK-5-CHANGED: Interface Serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up

%LINK-5-CHANGED: Interface FastEthernet7/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet7/0, changed state to up

 

 

 

 

Router con0 is now available

 

 
Press RETURN to get started.

 

 

 

 

 

 

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#ip address 192.168.4.10 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#

 

 

 
Router con0 is now available

 

 
Press RETURN to get started.

 

 

 

 

 

 

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router ospf 90
Router(config-router)#network 10.10.3.2 255.255.255.252 are 9
Router(config-router)#network 10.10.3.2 255.255.255.252 are 9
00:58:04: %OSPF-5-ADJCHG: Process 90, Nbr 192.168.3.10 on Serial2/0 from LOADING to FULL, Loading Done

Router(config-router)#network 10.10.3.0 255.255.255.252 are 9
Router(config-router)#network 10.10.4.0 255.255.255.252 are 9
Router(config-router)#network 10.10.4.0 255.255.255.252 are 9
00:59:10: %OSPF-5-ADJCHG: Process 90, Nbr 192.168.2.10 on Serial3/0 from LOADING to FULL, Loading Done

Router(config-router)#network 10.10.4.0 255.255.255.252 area 9
Router(config-router)#network 10.10.3.0 255.255.255.252 area 9
Router(config-router)#network 192.168.4.0 255.255.255.0 area 9
Router(config-router)#log-adjecency-changes
^
% Invalid input detected at ‘^’ marker.

Router(config-router)#log-adjacency-changes
Router(config-router)#end

%SYS-5-CONFIG_I: Configured from console by console
Router#write
Building configuration…
[OK]
Router#
Router#
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router ospf 90
Router(config-router)#network 10.10.5.0 255.255.255.252 area 9
Router(config-router)#log-adjancency
01:04:32: %OSPF-5-ADJCHG: Process 90, Nbr 192.168.1.10 on FastEthernet7/0 from LOADING to FULL, Loading Do
^
% Invalid input detected at ‘^’ marker.

Router(config-router)#log-adjancency-changes
^
% Invalid input detected at ‘^’ marker.

Router(config-router)#log-adjacency-changes
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#write
Building configuration…
[OK]

Standard

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s